Glossary
147 terms on UPS, batteries, power quality and energy, explained simply.
147 terms
A
- AC ChargingCharging with alternating current, where the vehicle's on-board charger converts it to direct current to fill the battery.Technical level: Basic
- AC EfficiencyIndicates how efficiently a UPS converts incoming AC power into usable output power during normal operation.Technical level: Intermediate
- AC RippleA small unwanted AC component on the DC charging voltage of a UPS that heats the batteries and shortens their life.Technical level: Advanced
- AGM BatteryA sealed VRLA lead-acid battery whose electrolyte is absorbed in glass-fibre mat separators.Technical level: Basic
- Alarm ContactA relay output on a UPS that changes state on an alarm, such as battery mode, low battery or a fault, to alert an external system.Technical level: Intermediate
- Altitude DeratingReduction in the rated power of a UPS, inverter or generator when it is installed above a certain altitude, usually 1,000 metres.Technical level: Advanced
- Ambient TemperatureThe surrounding temperature of the environment where UPS or batteries are installed.Technical level: Basic
- Ampere-hour (Ah)The unit of battery capacity, showing how much current a battery can deliver and for how long, e.g. 9 Ah means 0.45 A for 20 hours.Technical level: Basic
- ATS (Automatic Transfer Switch)A device that automatically moves the load from the grid to a generator during an outage and back again when grid power returns.Technical level: Intermediate
- Auto RestartA UPS feature that automatically restarts the system after utility power returns following a shutdown.Technical level: Basic
- Automatic Voltage Regulator (AVR)A device that automatically maintains a constant voltage level to protect electrical equipment from fluctuations.Technical level: Basic
- AutonomyThe time a battery-powered system (like a UPS) can continue operating critical loads after a power failure.Technical level: Basic
B
- Battery BankA group of batteries connected together to increase total backup time or capacity.Technical level: Intermediate
- Battery Charging CurrentThe amount of current supplied to charge a battery, regulated by the UPS system.Technical level: Intermediate
- Battery Management System (BMS)A system that monitors and manages the performance, health, and charging of batteries.Technical level: Intermediate
- Battery Service LifeThe years a battery keeps enough capacity, typically 3–5 years for VRLA at 20–25 °C, shortened by high temperatures.Technical level: Basic
- BlackoutA complete and sudden loss of grid power, lasting anywhere from seconds to several hours.Technical level: Basic
- BypassA path that feeds the load directly from the mains, without protection, when the UPS is overloaded, faulty or under maintenance.Technical level: Intermediate
C
- C-rateThe charge or discharge current expressed as a multiple of battery capacity, e.g. 1C for a 100 Ah battery means 100 A.Technical level: Advanced
- Capacity SystemParallel UPS units that share the load with no spare unit (N configuration), so the failure of one unit overloads the rest.Technical level: Advanced
- CCS2 (Combined Charging System)The European connector standard that adds two DC pins below a Type 2 plug, allowing fast DC charging through the same vehicle inlet.Technical level: Basic
- CHAdeMOA Japanese DC fast-charging standard with its own separate connector, now giving way to CCS2 in Europe.Technical level: Intermediate
- Charging Modes (Mode 1–4)The IEC 61851 classification of EV charging, from a plain socket with no communication (Mode 1) to a DC fast charger (Mode 4).Technical level: Intermediate
- Charging Power (kW)How much energy flows into the battery per hour, which in AC charging depends on voltage, current and the number of phases.Technical level: Intermediate
- Circuit ProtectionDevices such as fuses and circuit breakers that open the circuit on overcurrent or short circuit to prevent damage.Technical level: Intermediate
- Cold Start FunctionA feature that allows a UPS to be started directly from the battery without utility power.Technical level: Intermediate
- Cooling FanA built-in fan in UPS or batteries used to dissipate heat during operation.Technical level: Basic
- Cycle LifeThe number of charge and discharge cycles a battery withstands until its capacity falls, usually, to 80% of the original.Technical level: Intermediate
D
- DC ChargingFast charging in which the station converts power to direct current and feeds it straight into the battery, typically at 50 to 350 kW.Technical level: Basic
- DC EfficiencyMeasures how effectively a UPS converts battery power into output power during battery mode.Technical level: Intermediate
- DC VoltageRefers to the direct current (DC) voltage level, typically that of a UPS battery.Technical level: Basic
- Deep-Cycle BatteryA battery designed to be discharged deeply and recharged again and again without wearing out quickly.Technical level: Basic
- Depth of Discharge (DoD)The share of a battery's capacity that has been drawn in a discharge, where 100% means fully discharged.Technical level: Intermediate
- Double Conversion EfficiencyThe share of input power that an online UPS delivers to its output, lower at light load and highest at medium to high load.Technical level: Advanced
- Dry ContactA passive relay contact used to transmit status signals without applying voltage.Technical level: Intermediate
- Dynamic Load BalancingA function that continuously measures the building's consumption and automatically lowers the charging power so the supply limit is not exceeded.Technical level: Intermediate
E
- Electromagnetic Interference (EMI)Unwanted electrical noise or interference that can disrupt electronic equipment operation.Technical level: Intermediate
- EMC (Electromagnetic Compatibility)The ability of a device to work properly without being affected by electromagnetic interference and without causing any itself.Technical level: Advanced
- Emergency Power Off (EPO)A safety feature that allows immediate shutdown of power to connected systems in an emergency.Technical level: Intermediate
- Equalising ChargeA controlled charge at a higher than normal voltage that brings all cells of a lead-acid battery to the same state of charge.Technical level: Advanced
- Ethernet Port (RJ45)The UPS's Ethernet network port, through which it can be monitored and controlled from any computer on the network via a browser, SNMP or shutdown software.Technical level: Basic
- Eurobat Design Life ClassesA classification of sealed lead-acid batteries by their design life on float charge at 20 °C.Technical level: Intermediate
- EV Connector Type 2The standard AC charging connector for electric vehicles in Europe, also known as Mennekes.Technical level: Basic
F
- Fast ChargingA charging method that restores battery capacity quickly without damage by controlling current, voltage and temperature.Technical level: Intermediate
- Float ChargingA continuous low-level charging method to keep UPS batteries full and prolong their lifespan.Technical level: Intermediate
- Flooded Lead-Acid BatteryA battery with liquid electrolyte and vent caps that needs regular checks and topping up with deionised water.Technical level: Intermediate
- FrequencyThe number of AC cycles per second, measured in hertz (Hz); the mains frequency in Europe is 50 Hz.Technical level: Basic
G
- GEL BatteryA sealed lead-acid battery with its electrolyte in gel form, well suited to deep and repeated discharges.Technical level: Basic
- GeneratorAn engine-driven alternator that produces electricity when the grid fails, often started automatically through an ATS.Technical level: Intermediate
- Ground FaultAn unintended flow of current from a live conductor to earth or to a device’s metal casing.Technical level: Intermediate
H
- Hardwired (Terminal Block) ConnectionPermanent connection of the UPS input or output by an electrician, with cables screwed into a terminal block instead of plugs and sockets, usually on higher-power UPS units.Technical level: Intermediate
- Harmonic DistortionDeviation of the waveform from a pure sine wave, caused mainly by non-linear loads such as power supplies and inverters.Technical level: Advanced
- Hot-swappable BatteriesBatteries that can be replaced without turning off the UPS or disconnecting the load.Technical level: Intermediate
I
- IEC C13/C14 ConnectorsStandardised pair of connectors rated up to 10 A under IEC 60320, found on UPS outputs and on the power supplies of computers, servers and monitors.Technical level: Basic
- IEC C19/C20 ConnectorsPair of connectors rated up to 16 A under IEC 60320, used on higher-power UPS units, rack PDUs and servers or switches with high-consumption power supplies.Technical level: Intermediate
- IK Rating (Impact Protection)Scale from IK00 to IK10 under IEC 62262 that shows how much impact energy the enclosure of an electrical device can withstand.Technical level: Intermediate
- Input Power CordThe cable that connects the UPS to the wall socket or distribution board, i.e. to its AC power source.Technical level: Basic
- Input Voltage WindowThe range of mains voltage within which a UPS keeps powering the load from the grid without switching to battery.Technical level: Intermediate
- Inrush CurrentThe initial surge of current required when electrical equipment is first powered on.Technical level: Intermediate
- InverterThe component inside a UPS that converts DC power from batteries back to usable AC power.Technical level: Intermediate
- IP Rating (Ingress Protection)Two-digit code under IEC 60529 in which the first digit shows protection against dust and solid objects and the second against water.Technical level: Basic
- IsolationSeparation of input and output with no conductive connection, usually through a transformer, to protect against faults and noise.Technical level: Intermediate
K
L
- LiFePO4 (Lithium Iron Phosphate) BatteryA lithium battery with an iron phosphate cathode, a nominal 3.2 V per cell, high thermal stability and thousands of cycles.Technical level: Intermediate
- Line ConditionerA device that improves power quality by regulating voltage and filtering noise.Technical level: Intermediate
- Line Interactive UPSA UPS that corrects voltage sags and swells with an automatic voltage regulator and switches to battery only when the voltage is lost or out of range.Technical level: Intermediate
- Lithium-ion BatteryA rechargeable lithium-ion battery with high energy density, long life and faster charging than lead-acid batteries.Technical level: Intermediate
- LoadAny device or system connected to a power source and drawing electrical current.Technical level: Basic
- Load SheddingA method used to prioritize power delivery by disconnecting non-critical loads during outages.Technical level: Intermediate
M
- Maintenance BypassA manual switch used to isolate the UPS for servicing while still supplying power to the load.Technical level: Intermediate
- ModbusA communication protocol used for connecting industrial electronic devices, including UPS systems.Technical level: Advanced
- Modular UPSA UPS design where independent modules can be combined to meet power and redundancy needs.Technical level: Intermediate
- MTBFThe average operating time between failures of a device, used as a measure of its reliability.Technical level: Intermediate
- MTTR (Mean Time To Repair)The average time it takes to repair a system after a failure occurs.Technical level: Intermediate
N
- Network Management Card (NMC)An interface card enabling remote monitoring and control of UPS systems via network.Technical level: Intermediate
- Noise (Electrical)Unwanted high-frequency disturbances on the supply voltage, e.g. from motors or power supplies, which UPS systems and line conditioners filter out.Technical level: Intermediate
- NUT (Network UPS Tools)Open-source software that reads the UPS status and shares it over the network, so that several servers and NAS devices can shut down in a coordinated way.Technical level: Advanced
O
- OCPP (Open Charge Point Protocol)An open communication protocol between a charging station and central management software, used for remote control, billing and monitoring.Technical level: Advanced
- Offline (Standby) UPSA UPS that leaves the load on the mains and switches to battery only when the mains fails, with a short transfer time; the simplest and cheapest topology.Technical level: Basic
- On-board Charger (OBC)The converter inside an electric vehicle that turns the station's AC into DC and sets the maximum AC charging power.Technical level: Intermediate
- Online (Double Conversion) UPSA UPS that continuously converts incoming AC to DC and back to AC, so the load is always fed by the inverter with clean, stable power.Technical level: Intermediate
- Operating Temperature and Humidity RangeThe limits of room temperature and relative humidity within which a device is designed to operate correctly.Technical level: Basic
- OPzS / OPzV Tubular BatteryStationary 2 V lead-acid cells with tubular positive plates, flooded (OPzS) or sealed with gel (OPzV), built for a very long life.Technical level: Advanced
- Overcurrent ProtectionA system designed to interrupt excessive current to protect UPS and loads.Technical level: Intermediate
- OverloadA condition where the connected load exceeds the UPS’s rated output in VA or W.Technical level: Intermediate
- OvervoltageA voltage above normal that lasts from seconds to hours and can stress or damage connected equipment.Technical level: Intermediate
P
- Patch PanelA rack panel with a row of ports where network cables terminate, so connections can be organised and changed easily.Technical level: Basic
- PDU (Power Distribution Unit)A rack power strip that distributes UPS power to the equipment, optionally with metering or remote control.Technical level: Basic
- Peak LoadThe highest amount of power drawn by connected equipment during operation.Technical level: Intermediate
- PhaseEach conductor carrying alternating voltage in an AC system; supplies are single-phase or three-phase depending on their number.Technical level: Intermediate
- Power ConditioningTechniques such as EMI/RFI filtering, surge protection and AVR that correct voltage problems before they reach the load.Technical level: Intermediate
- Power FactorThe ratio of real power (W) to apparent power (VA), from 0 to 1, showing how many watts a UPS can deliver per VA.Technical level: Intermediate
- Pure Sine WaveUPS output with the same waveform as the mains, needed for PFC power supplies, motors and sensitive equipment, unlike a stepped approximation.Technical level: Intermediate
- PV InverterA device that converts DC electricity from solar panels into AC electricity for use or grid feed-in.Technical level: Intermediate
R
- Rack Unit (U)A standard height unit for equipment in 19-inch racks, where 1U equals 44.45 mm.Technical level: Basic
- Rack-Mount UPSA UPS designed to fit a standard 19-inch rack, with its height measured in rack units (U).Technical level: Basic
- Rectifier/ChargerA UPS component that converts AC to DC and charges the battery.Technical level: Intermediate
- RedundancyHaving more UPS units or modules than the load needs, typically in an N+1 or 2N configuration, so the load stays powered if one fails.Technical level: Intermediate
- Redundant Power SupplyA second power supply inside a server or switch that takes over without interruption if the first one fails or loses its feed.Technical level: Intermediate
- Remote MonitoringThe ability to observe and manage UPS performance over a network from another location.Technical level: Intermediate
- RFI — Radio Frequency InterferenceA subset of EMI: high-frequency noise from electronic equipment that can disturb radio, Wi-Fi and other devices.Technical level: Intermediate
- RFID AuthenticationContactless identification with a card or key fob, so that only authorised users can start a charging session at a station.Technical level: Basic
- RightsizingSelecting UPS capacity to match current load and scale with future needs, avoiding over-sizing.Technical level: Intermediate
- RS-232Point-to-point serial communication standard, usually on a DB9 connector, for linking a UPS to one computer over a distance of a few metres.Technical level: Intermediate
- RS-485Differential serial interface over a wire pair that links many devices on one bus over long distances, usually with the Modbus RTU protocol.Technical level: Advanced
S
- ScalabilityThe ability of a UPS system to expand capacity by adding additional modules or batteries.Technical level: Intermediate
- Schuko SocketThe common 16 A socket with side earthing clips used in Greece and much of Europe, found on many small UPS units.Technical level: Basic
- Self-dischargeThe gradual loss of charge in a battery kept in storage without use, caused by internal chemical reactions.Technical level: Basic
- Serial NumberThe unique code of each device, printed on its label, which you need for warranty and repairs.Technical level: Basic
- Serial PortA communication port on a UPS used to connect and transmit signals to computers or monitoring equipment.Technical level: Intermediate
- Short CircuitAn unintended low-resistance connection between conductors that causes a sudden, dangerous surge of current.Technical level: Intermediate
- Shutdown SoftwareSoftware that talks to the UPS and automatically shuts down servers and computers safely before the battery runs out.Technical level: Intermediate
- Signal ConditioningFiltering and stabilising the power or signal on a line so that it reaches the device clean and free of interference.Technical level: Advanced
- Single-phase PowerAn electrical system with one alternating current (AC) voltage phase, commonly used in homes and offices.Technical level: Basic
- Six Nines AvailabilityAvailability of 99.9999%, about 32 seconds of downtime a year, which requires redundancy across the whole power chain.Technical level: Advanced
- Smart ChargingCharging that adapts current and voltage to battery condition and temperature, or an EV charger’s power to the site’s available capacity.Technical level: Intermediate
- SNMPA standard network protocol used to monitor and control devices like UPS systems over a network.Technical level: Intermediate
- Solar Surplus Charging (PV Charging)A charger function that uses surplus solar production to charge the vehicle instead of exporting it to the grid.Technical level: Intermediate
- State of Charge (SoC)A battery's current charge level as a percentage of its capacity, from 0% (empty) to 100% (fully charged).Technical level: Basic
- Static BypassAn electronic path inside the UPS that instantly and automatically transfers the load to the mains on overload or internal fault.Technical level: Intermediate
- Static SwitchA thyristor-based switch with no moving parts that transfers the load between inverter and mains within a fraction of a cycle.Technical level: Advanced
- Surge ProtectorA device that limits brief voltage spikes from lightning or grid switching by diverting the excess energy to earth.Technical level: Basic
T
- Thermal RunawayAn uncontrolled temperature rise in a battery, where heat speeds up currents or reactions that produce even more heat.Technical level: Advanced
- Three-phase PowerA supply with three AC phases shifted by 120° (400 V between phases), used for large loads, motors and UPS systems from about 10 kVA.Technical level: Intermediate
- Total Cost of Ownership (TCO)The total cost of a UPS over its whole life: purchase, installation, energy, maintenance and battery replacement.Technical level: Intermediate
- Transfer SwitchA manual or automatic switch that connects the load to one of two sources, such as the grid and a generator, never both at once.Technical level: Intermediate
- Transfer TimeThe brief power gap when a UPS switches from mains to battery, typically 2–10 ms for line-interactive models and zero for online ones.Technical level: Intermediate
- TransformerAn electrical component that changes voltage levels or isolates circuits.Technical level: Intermediate
- Transformer-Based UPSTraditional UPS design using internal transformers to regulate voltage and provide isolation.Technical level: Advanced
- Transformerless UPSModern UPS design that omits bulky transformers to improve efficiency and reduce size.Technical level: Advanced
- Type A vs Type B RCD (6 mA DC Leakage Detection)The residual current protection of an EV charger must also cover DC leakage, using either a Type B RCD or a Type A RCD plus 6 mA DC detection.Technical level: Advanced
U
- UndervoltageA sustained drop of mains voltage below normal that can cause malfunctions or overheat motors.Technical level: Basic
- UPS (Uninterruptible Power Supply)A device that provides backup power and protects equipment from power disturbances.Technical level: Basic
- USB HID (Power Device Class)Standard USB device class through which a UPS appears in Windows and macOS as a battery, without installing any drivers.Technical level: Intermediate
- USB PortA USB interface used for communication between UPS and computers.Technical level: Basic
- User-Replaceable BatteriesUPS batteries that users can safely replace on their own, without needing a technician.Technical level: Basic
V
- Volt (V)The unit of electrical voltage; in Europe mains voltage is 230 V single-phase and 400 V three-phase.Technical level: Basic
- Voltage DropA decrease in voltage level in a circuit due to resistance or high load.Technical level: Basic
- Voltage Regulation RangeThe input voltage range over which a UPS or stabilizer keeps its output close to 230 V without drawing on the battery.Technical level: Intermediate
- Voltage SpikeA momentary, very high voltage rise lasting microseconds, e.g. from lightning or load switching, that can damage equipment.Technical level: Intermediate
- VRLA BatteryA sealed, valve-regulated lead-acid battery that never needs topping up with water and is used in most UPS systems.Technical level: Intermediate
W
- Wake-on-LAN (WoL)Network card feature that starts a powered-off computer or server when it receives a special network packet, the magic packet.Technical level: Intermediate
- Wallbox (home wall charger)A wall-mounted EV charger that charges with AC from its own circuit in the panel and communicates with the vehicle for safe charging.Technical level: Basic
- WarrantyThe manufacturer’s commitment to repair or replace a device that develops a defect within a set period.Technical level: Basic
- Watt (W)The unit of real power; on a UPS it shows how much power connected equipment can actually draw.Technical level: Basic
Z
A question about your device?
Find answers, guides and software, or ask our team for help.